Fire-LCA study of TV sets with V0 and HB enclosure material

A novel Life-Cycle Assessment model (Fire-LCA) has been defined for the determination of the environmental impact of measures taken to attain a high level of fire safety. This study, which represents the first application of this LCA model, concentrates on a comparison between a TV with an enclosure manufactured with a flame retardant (FR) plastic (V0-rated high impact polystyrene, HIPS, typical for the US market) and one manufactured with a non-flame retardant (HB-rated HIPS, typical for the European market). A fire model has been defined based on international statistics, which indicate that use of V0 rated enclosure material essentially removes the risk of TV fires while approximately 165 TV fires occur per million TVs in Europe each year where the enclosure material is breached. The application of the model indicates that emissions of some key species (such as dibenzodioxins and PAH) are actually lower for the TV with the FR enclosure than for the TV with the NFR enclosure. This has direct reprercussions for the assessment of the environmental impact of the FR TV relative to that of the NFR TV. Finally, when considering the risk associated with the use of flame retardants, it is also important to consider the risk associated with fires. Based on the in-depth analysis of available fire statistics, conducted as a part of this study, it has been estimated that as many as 160 people may die each year in Europe as a direct result of TV fires and as many as 2000 may be injured in the same period.     

Concentration and size distribution of ultrafine particles near a major highway

Motor vehicle emissions usually constitute the most significant source of ultrafine particles (diameter <0.1 microm) in an urban environment, yet little is known about the concentration and size distribution of ultrafine particles in the vicinity of major highways. In the present study, particle number concentration and size distribution in the size range from 6 to 220 nm were measured by a condensation particle counter (CPC) and a scanning mobility particle sizer (SMPS), respectively. Measurements were taken 30, 60, 90, 150, and 300 m downwind, and 300 m upwind, from Interstate 405 at the Los Angeles National Cemetery. At each sampling location, concentrations of CO, black carbon (BC), and particle mass were also measured by a Dasibi CO monitor, an aethalometer, and a DataRam, respectively. The range of average concentration of CO, BC, total particle number, and mass concentration at 30 m was 1.7-2.2 ppm, 3.4-10.0 microg/m3, 1.3-2.0 x 10(5)/cm3, and 30.2-64.6 microg/m3, respectively. For the conditions of these measurements, relative concentrations of CO, BC, and particle number tracked each other well as distance from the freeway increased. Particle number concentration (6-220 nm) decreased exponentially with downwind distance from the freeway. Data showed that both atmospheric dispersion and coagulation contributed to the rapid decrease in particle number concentration and change in particle size distribution with increasing distance from the freeway. Average traffic flow during the sampling periods was 13,900 vehicles/hr. Ninety-three percent of vehicles were gasoline-powered cars or light trucks. The measured number concentration tracked traffic flow well. Thirty meters downwind from the freeway, three distinct ultrafine modes were observed with geometric mean diameters of 13, 27, and 65 nm. The smallest mode, with a peak concentration of 1.6 x 10(5)/cm3, disappeared at distances greater than 90 m from the freeway. Ultrafine particle number concentration measured 300 m downwind from the freeway was indistinguishable from upwind background concentration. These data may be used to estimate exposure to ultrafine particles in the vicinity of major highways.     

The interaction effects of binary mixtures of benzene and toluene on the developing heart of medaka (Oryzias latipes)

The United States Environmental Protection Agency (USEPA) has pursued the estimation of risk of adverse health effects from exposure to chemical mixtures since the early 1980s. Methods used to calculate risk estimates of mixtures were often based on single chemical information that required assumptions of dose-addition or response-addition and did not consider possible changes in response due to interaction effects among chemicals. Full factorial designs for laboratory studies can produce interactions information, but these are expensive to perform and may not provide the information needed to evaluate specific environmentally relevant mixtures. In this research, groups of Japanese medaka (Oryzias latipes) embryos were exposed to binary mixtures of benzene and toluene as well as to each of these chemicals alone. Endpoint specific dose-response models were built for the hydrocarbon mixture under an assumption of dose-additivity, using the single chemical dose-response information on benzene and toluene. The endpoints included heart rate, heart rate progression, and lethality. Results included a synergistic response for heart rate at 72 h of development, and either additivity or antagonism for all other endpoints at 96 h of development. This work uses an established statistical method to evaluate the toxicity of an environmentally relevant mixture to ascertain whether interaction effects are occurring, thus providing additional information on toxicity.     

Atmospheric versus biological sources of polycyclic aromatic hydrocarbons (PAHs) in a tropical rain forest environment

To distinguish between pyrogenic and biological sources of PAHs in a tropical rain forest near Manaus, Brazil, we determined the concentrations of 21 PAHs in leaves, bark, twigs, and stem wood of forest trees, dead wood, mineral topsoil, litter layer, air, and Nasutitermes termite nest compartments. Naphthalene (NAPH) was the most abundant PAH with concentrations of 35 ng m(-3) in air (>85% of the sum of 21PAHs concentration), up to 1000 microg kg(-1) in plants (>90%), 477 microg kg(-1) in litter (>90%), 32 microg kg(-1) in topsoil (>90%), and 160 microg kg(-1) (>55%) in termite nests. In plants, the concentrations of PAHs in general decreased in the order leaves > bark > twigs > stem wood. The concentrations of most low-molecular weight PAHs in leaves and bark were near equilibrium with air, but those of NAPH were up to 50 times higher. Thus, the atmosphere seemed to be the major source of all PAHs in plants except for NAPH. Additionally, phenanthrene (PHEN) had elevated concentrations in bark and twigs of Vismia cayennensis trees (12-60 microg kg(-1)), which might have produced PHEN. In the mineral soil, perylene (PERY) was more abundant than in the litter layer, probably because of in situ biological production. Nasutitermes nests had the highest concentrations of most PAHs in exterior compartments (on average 8 and 15 microg kg(-1) compared to <3 microg kg(-1) in interior parts) and high PERY concentrations in all compartments (12-86 microg kg(-1)), indicating an in situ production of PERY in the nests. Our results demonstrate that the deposition of pyrolytic PAHs from the atmosphere controls the concentrations of most PAHs. However, the occurrence of NAPH, PHEN, and PERY in plants, termite nests, and soils at elevated concentrations supports the assumption of their biological origin.     

PM10-bound polycyclic aromatic hydrocarbons (PAHs) in the Greater Area of Athens, Greece

Polycyclic aromatic hydrocarbons (PAHs) associated to ambient PM10 were determined at four sites within the Greater Athens Area (GAA), Greece, during the period May 2001-June 2002. Daily average PM10 samples were collected using reference samplers installed in two urban locations (Maroussi, MAR and Aristotelous, ARI), a mixed urban-industrial location (Elefsina, ELE), and a background location (Thracomacedones, THR). Spatial and temporal variation of ambient PAH levels and possible relationships with conventional air pollutants and meteorological parameters were investigated. Moreover, source identification was attempted using diagnostic ratios. The PAH concentrations observed in this study, even in downtown Athens, were towards the lowest end of the range of values reported for other European urban locations. The mean concentration of the well known carcinogen B[alpha]Py was at all four sites below the proposed value of 1 ng m-3 (annual average assessment threshold). Automobile traffic was identified as the major PAH source in the GAA exhibiting greatest contribution in the urban sites.     

Size distribution of airborne particulate matter and associated heavy metals in the roadside environment

The size distributions of airborne particulate matter (PM) and associated heavy metals Pb, Cd, Ni, Cr, V, Mn, Cu and Fe in different inhalable fractions (< 0.8 microm, 0.8-1.3 microm, 1.3-2.7 microm, 2.7-6.7 microm and > 6.7 microm) were determined at a traffic-orientated urban site in the city of Thessaloniki, northern Greece. The airborne PM displayed a bimodal distribution with most of the mass (52%) contained in the submicron size range (< 0.8 microm) and an additional minor mode (20%) in the coarse size fraction (> 6.7 microm). Characteristic size distributions of heavy metals allowed identification of three main behavioral types: (a) metals whose mass was resided mainly within the accumulation mode (Pb,Cd), (b) those which were distributed between fine, intermediate and coarse modes (Ni,Cu,Mn), and (c) those which were mainly found within particles larger than 2.7 microm in diameter (Fe). The mean mass median aerodynamic diameter (MMAD) of PM was found at 0.85+/-0.71 microm, while the mean MMADs of heavy metals followed the order Pb (0.96 +/- 0.71 microm) < Cd (1.14 +/- 0.82 microm) < V (1.38 +/- 0.63 microm) < Ni (1.45 +/- 0.88 microm) < Cu (2.04 +/- 0.77 microm) < Mn (2.61 +/- 1.23 microm) < Cr (2.91 +/- 1.40 microm) < Fe (3.82 +/- 0.88 microm). The measured distributions are believed to result from a combination of processes including local anthropogenic and natural sources, such as traffic, industrial emissions and resuspension of road dust.     

Tracing the influence of sewage nitrogen in a coastal ecosystem using stable nitrogen isotopes

This paper reviews the use of stable nitrogen isotopes (delta15N) to delineate the influence of sewage nitrogen (N) in coastal ecosystems, drawing extensively on the case of Himmerfj?rden, a Baltic Sea bay that receives 15N-enriched tertiary treated sewage that is discharged mainly as dissolved inorganic N (DIN). Gradients of delta15N in macroalgae (Fucus vesiculosus) and surface sediments traced sewage-derived N to 24 km from the outfall but elevated delta15N values (> 7 per thousand) indicated that the sewage influence was most pronounced within 10 km. Comparison of macroalgal delta15N values before and after enhanced tertiary treatment showed a decrease in the spatial impact of sewage N from about 24 km to 12 km from the outfall and a decrease to more marine delta15N values in more recent growth tissues. Sedimentary delta15N records showed that sewage has had a dominant influence on organic matter production in the bay with dramatic increases in sedimentary delta15N during the years of maximum sewage N loads. In cases where sewage N introduces a distinct isotopic signature into a system and where it has had a dominant influence on organic matter production, delta15N values in biota and sediments can be used to trace the spatial and temporal influence of sewage N in aquatic ecosystems.     

Formation of PCDD/Fs in the sintering process: role of the grid-Cr2O3 catalyst in the de novo synthesis

The sintering process is among the major sources of the very toxic polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in the environment. At the industrial scale, it has been shown that dust collected on the grid, which supports the feed, contains PCDD/Fs amounts between the values found in the bottom of the cake and the values found on dust collected during gas sampling in the wind boxes. This fact suggests that the grid, containing 25wt.% of chromium, could have a catalytic activity in PCDD/Fs formation during the sintering process. This research tries to study this potential role. The de novo synthesis of PCDD/Fs is simulated at laboratory scale by thermal treatments of samples mixed with grid filings or Cr2O3. The thermal experiments performed with E.S.P. dust (dust collected in the electrostatic precipitator of a sintering plant) or graphite mixed with grid filings do not allow to confirm a role of the grid in PCDD/Fs formation during the industrial process. On the other hand, it has been shown that Cr2O3 can be considered as a catalyst in the de novo synthesis of PCDD/Fs. This compound takes place in the two steps of the de novo synthesis: the degradation of the carbon matrix as well as the chlorination reactions.     

Photocatalytic degradation of azo dyes by nitrogen-doped TiO2 nanocatalysts

This study examined the photocatalytic degradation of three azo dyes, acid orange 7 (AO7), procion red MX-5B (MX-5B) and reactive black 5 (RB5) using a new type of nitrogen-doped TiO2 nanocrystals. These newly developed doped titania nanocatalysts demonstrated high reactivity under visible light (lambda>390 nm), allowing more efficient usage of solar light. The doped titania were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Experiments were conducted to compare the photocatalytic activities of nitrogen-doped TiO2 nanocatalysts and commercially available Degussa P25 powder using both UV illumination and solar light. It is shown that nitrogen-doped TiO2 after calcination had the highest photocatalytic activity among all three catalysts tested, with 95% of AO7 decolorized in 1 h under UV illumination. The doped TiO2 also exhibited substantial photocatalytic activity under direct sunlight irradiation, with 70% of the dye color removed in 1h and complete decolorization within 3 h. Degussa P25 did not cause detectable dye decolorization under identical experimental conditions using solar light. The decrease of total organic carbon (TOC) and evolution of inorganic sulfate (SO4(2-)) ions in dye solutions were measured to monitor the dye mineralization process.     

Temporal variation of trace metal geochemistry in floodplain lake sediment subject to dynamic hydrological conditions

Climate change and land use may significantly influence metal cycling in dynamic river systems. We studied temporal variation of sediment characteristics in a floodplain lake, including concentrations of dissolved organic carbon, acid volatile sulfide and trace metals. The sampling period included a severe winter inundation and a dramatic water level drop during summer. Temporal changes were interpreted using multivariate analysis and chemical equilibrium calculations. Metal concentrations in sediment increased with depth, indicating a gradual improvement of sediment quality. In contrast, dissolved metal concentrations were highest in top layers due to mobilization from oxyhydroxides and precipitation with sulfides in deeper layers. Inundation had a mobilizing effect as it stimulated resuspension and oxygenation of sediment top layers. Water table lowering combined with organic matter decomposition led to immobilization due to sulfide formation. The chemistry of the sediments was consistent with model calculations, especially for macro-elements. The results illustrate the importance of seasonality for metal risk assessment.